How to wash dirt and remove rust from the toilet at home?

How to clean the toilet from rust? This question is asked by many housewives who dream of maintaining the cleanliness and pleasant appearance of plumbing fixtures in the bathroom.

Where does rust come from?

The causes of rust spots on the surface of the toilet can be different. Often the cause is the chemical composition of water. Rust is caused by the abundance of various salts of iron in tap water. It is possible to deal with such a problem - for this, special capsules or tablets should be added to the tank. They change the chemical composition of water, neutralizing harmful compounds, and also give the water a pleasant smell.

If the quality of tap water is not in doubt, then the source of rust may be old pipes made of galvanized steel. The way out is to either add tablets to the drain tank in the same way, or replace the pipes with polypropylene or metal-plastic ones.

The appearance of stains, including rust, contributes to the rough surface of the toilet, for which the pollution "cling". This problem is typical for faience toilets. But porcelain have a smoother surface, which gets dirty much less, and less rust is removed from the toilet.

Rusty marks are also guaranteed if the tank leaks and water constantly flows from it in a thin stream. To remove rust from the toilet for a long time in this case will not work until the malfunction is fixed.

In order not to do the regularly pointless work of cleaning the surface of the toilet, you should try to remove or minimize the causes of rust.

How to remove rust?

The whole wide range of rust stain control agents can be divided into two large groups - folk and shop.

Household chemicals

1. Abrasive. This group includes all products whose cleaning effect is based on the mechanical effect of powder particles on pollution. An example of such a tool is the well-known Pemolux. Such a tool should be applied to a rag or sponge and rub the rust stain until it disappears completely. Although such products are ultimately quite effective, stain removal takes a lot of time. In addition, small, sharp fragments of powder scratch the surface, which means that subsequently pollution will be easier to form on it.
2. Alkaline. They act by dissolving contamination without mechanical harm to the surface. Such funds are applied to the stain for 10-15 minutes, and then washed off with water. They are considered quite effective, but old pollution is not always possible to wash them.
3. Acidic. Like alkaline, such substances simply dissolve pollution. Remove any kind of stains, even the oldest ones. But due to the high aggressiveness of such products, working with them at home is recommended when wearing gloves, and also to avoid getting them on exposed skin and eyes. Acids are great for earthenware and porcelain toilets, but you should not use them for enameled baths - they dissolve the enamel.

Tip

Do not mix several household chemicals - this can lead to unpredictable chemical reactions and damage to the surface of the toilet.

Folk recipes

1. Vinegar. A rag moistened in vinegar essence is placed for half an hour - an hour on a contaminated area, after which this place is rinsed with water.
2. Peroxide and ammonia. Mixed in a ratio of 1 to 10, these two substances are applied to the stain for several hours.
3. Oxalic acid. The product is applied to rust for about an hour, after which this place should be wiped with a sponge moistened with ammonia, and then rinsed with plenty of water.
4. Hydrochloric acid. A rusty stain is poured with acid, left for several minutes, rinsed with water.

Little tricks

How to remove rust from the toilet if there is no cleaning agent at hand?

1. You can remove small stains with toothpaste. It should be applied to a rusty area and brushed.
2. It is believed that rust and limescale on plumbing fixtures can be washed with drinks such as Kola, Sprite, Fanta, etc. You should moisten a rag with them and leave it dirty for a while, and then rinse this place water.
3. Electrolyte from batteries copes well with spots, although this is not its main purpose. The liquid is applied to the stain for a quarter of an hour, and then washed off.

In order for the plumbing to shine and delight the eye with whiteness, it is necessary to timely eliminate all its breakdowns and conduct regular cleaning. It is obvious that recently appeared contaminants are much easier to wash than stubborn old spots. And when buying plumbing, it is worth giving preference to devices with a special water-repellent glaze, which will prevent the appearance of contaminants.