9 ways to fold your headphones so that they don’t get confused

Many owners of smartphones use headphones: listen to music or audio books. However, after using the accessory, you need to somehow fold the headphones and put it in a bag or pocket until next time. Alas, before the next use, the wires are often randomly confused. How to avoid this? There are ways to quickly and accurately fold the headphones, with which you can avoid breaking a convenient gadget.

Basic method

The first method is very simple - perhaps this is how most people fold the headphone wires.

1. First you need to put the device in order, unwinding it if the wires are tangled.
2. Untangled wires must be placed on the palm of your left hand, carefully straightened.
3. Holding the speaker with your thumb, wrap the wire with your right hand, wrapping it several times around the palm of your hand, leaving a “tail” of 8–9 cm long.
4. Release the twisted wire and wrap the remaining “tail” around the wires that were removed from the palm of your hand.

Keeping your headphones in this form is convenient and safe.

"Goat"

This method is suitable not only for old-school rockers, but also for everyone who does not want to unravel the wiring in order to listen to music from a smartphone.

1. It is necessary to protrude the index finger and the little finger of the left hand, bend the middle and ring fingers, depicting the notorious "goat", as at a rock concert.
2. Clamp the “ears” of the headset with the index finger and thumb, and wire the wires to the little finger.
3. Wrap the cable around the index finger and little finger with the figure eight. At the end, leave 8-10 cm of unwound wire.
4. Unwound wire should be wrapped around the center of the eight, plug the plug into one of the loops.

"Scout"

When laying the headphones in the Scout mode, you need to work with three fingers: index, middle and ring fingers.

1. Press the "ears" of the accessory thumb to the index.
2. Gently wind the wire on the protruding fingers. When about 10 cm of cable remains, the wound wire is removed from the fingers.
3. The left part is fixed to the wire by winding it in the middle.
4. The end is threaded into one of the loops and carefully tightened.

The device is securely wound; to unwind it, you will need to remove the plug from the loop and pull it.

Credit card

In this method, you will need an unnecessary plastic card - bank or discount. On it, on the sides, you need to make recesses and twist the wires of the headphones, passing through them. At the end, pry the jack under the wire, and the free edge of the wire should be threaded into the hole made from above.

You can make 2 holes at the top of the card with a hole punch that match the size of the speakers. The hole made below is for the plug. To store the accessory, you need to insert the “ears” into your “houses” (holes), wind the wires around the plastic, insert the plug into the hole from below.

The method is simple, reliable, and the old, obsolete plastic card is not difficult to find.

Bung

A cork from a wine bottle can be used to securely twist the headphones so that they are safe - there are no sharp ends on the soft cork. This method is suitable for carrying in a bag or in a backpack.

On the back of the cork you need to cut a narrow recess so that the plug in it can comfortably hold. The rest of the wire should be wound around the cork. Get a convenient fixture.

Binder

This method is suitable for office employees who have access to large stationery clips - binders

Around the binder, the headphone wire is folded, the jack is fixed by inserting it inside.For carrying in a pocket, this method is not entirely convenient, but it suits perfectly for a bag and backpack.

Player or phone

The method is simple, use it for short-term storage of headphones with the gadget in your pocket.

To do this, wrap the wire around the phone or player. Jack is stuck in the audio jack. The method is convenient to hide headphones with a player for a short time (for example, for 2 hours).

For long-term storage, the method will not work, since the wire wound in this way can weaken over time and will dangle.

Special organizer

On the Internet and specialized stores there are various organizers on which you can wind the wire from the headphones for storage. They are equipped with clips for wires, with which the use of headphones is very convenient. If the wire is long, then the excess part can not be pulled from the organizer, but simply fix the required size and in this form use the earpiece for its intended purpose.

Homemade fixture

You can make the organizer yourself out of felt, leatherette.

The simplest option:

1. A circle of suitable size is cut out of the selected material and folded in half.
2. On the side of the arc of the semicircle, Velcro sticks.

The organizer is ready. You can decorate it by cutting out the pattern and pasting it from the skin onto or using the finished patch.

You can make a simple cardboard organizer.

1. For the manufacture of cut two circles of cardboard.
2. Between them, you need to glue the bottle cap from under the soda.
3. On one circle, a hole is made for the “ears” of the earphone, on the other - to insert the plug.

The choice of options is huge: you can make an organizer from different materials, and the shape, size and color can be chosen as you wish. Cheap, original, fast.

If these methods do not suit you, then you should think about purchasing a wireless headphone. Such a device has its own advantages and disadvantages, but with it you definitely will not have to worry about how to lay the device so that it does not get confused.

You can use one of these methods or take turns so that the headphones are not confused. Any method can facilitate the daily untangling of nodes.